Effect of the relative humidity on the fibre morphology of polyamide 4.6 and polyamide 6.9 nanofibres
- De Schoenmaker, Bert, Van de Schueren, Lien, Zugle, Ruphino, Goethals, Annelies, Westbroek, Philippe, Kiekens, Paul, Nyokong, Tebello, De Clerck, Karen
- Authors: De Schoenmaker, Bert , Van de Schueren, Lien , Zugle, Ruphino , Goethals, Annelies , Westbroek, Philippe , Kiekens, Paul , Nyokong, Tebello , De Clerck, Karen
- Date: 2013
- Subjects: To be catalogued
- Language: English
- Type: text , article
- Identifier: http://hdl.handle.net/10962/242131 , vital:51004 , xlink:href="https://doi.org/10.1007/s10853-012-6934-9"
- Description: To obtain uniform and reproducible nanofibres, it is important to understand the effect of the different electrospinning parameters on the nanofibre morphology. Even though a lot of literature is available on the electrospinning of nanofibres, only minor research has been performed on the effect of the relative humidity (RH). This paper investigates the influence of this parameter on the electrospinning process and fibre morphology of the hydrophilic polyamide 4.6 and the less hydrophilic polyamide 6.9. First, the electrospinning process and deposition area of the nanofibres is examined at 10, 50 and 70 % RH. Subsequently, the effect of the polyamide concentration and solvent ratio on the fibre morphology is investigated using scanning electron microscopy and differential scanning calorimetry. It was found that the nanofibre diameter decreased with increasing RH. This resulted in less stable crystals for polyamide 4.6 while electrospinning of polyamide 6.9 at higher RH led to slightly more stable crystals. In conclusion, the water affinity of a polymer is an important factor in predicting the nanofibre morphology at different humidities.
- Full Text:
- Date Issued: 2013
- Authors: De Schoenmaker, Bert , Van de Schueren, Lien , Zugle, Ruphino , Goethals, Annelies , Westbroek, Philippe , Kiekens, Paul , Nyokong, Tebello , De Clerck, Karen
- Date: 2013
- Subjects: To be catalogued
- Language: English
- Type: text , article
- Identifier: http://hdl.handle.net/10962/242131 , vital:51004 , xlink:href="https://doi.org/10.1007/s10853-012-6934-9"
- Description: To obtain uniform and reproducible nanofibres, it is important to understand the effect of the different electrospinning parameters on the nanofibre morphology. Even though a lot of literature is available on the electrospinning of nanofibres, only minor research has been performed on the effect of the relative humidity (RH). This paper investigates the influence of this parameter on the electrospinning process and fibre morphology of the hydrophilic polyamide 4.6 and the less hydrophilic polyamide 6.9. First, the electrospinning process and deposition area of the nanofibres is examined at 10, 50 and 70 % RH. Subsequently, the effect of the polyamide concentration and solvent ratio on the fibre morphology is investigated using scanning electron microscopy and differential scanning calorimetry. It was found that the nanofibre diameter decreased with increasing RH. This resulted in less stable crystals for polyamide 4.6 while electrospinning of polyamide 6.9 at higher RH led to slightly more stable crystals. In conclusion, the water affinity of a polymer is an important factor in predicting the nanofibre morphology at different humidities.
- Full Text:
- Date Issued: 2013
A study on the morphology of thin copper films on para-aramid yarns and their influence on the yarn’s electro-conductive and mechanical properties
- Schwarz, Anne, Hakuzimana, Jean, Westbroek, Philippe, Mey, Gilbert De, Priniotakis, Georgios, Nyokong, Tebello, Langenhove, Lieva Van
- Authors: Schwarz, Anne , Hakuzimana, Jean , Westbroek, Philippe , Mey, Gilbert De , Priniotakis, Georgios , Nyokong, Tebello , Langenhove, Lieva Van
- Date: 2012
- Subjects: To be catalogued
- Language: English
- Type: text , article
- Identifier: http://hdl.handle.net/10962/243487 , vital:51157 , xlink:href="https://doi.org/10.1177/0040517511431291"
- Description: The latest technological advances in new materials and devices enabled wearable systems to be created by utilizing textile solutions. These solutions require electro-conductive yarns as a basic component. Although the production of electroconductive yarn is widely reported, research is still necessary to characterize them to advance their electro-conductive and mechanical properties. Hence, we served this need and characterized copper-coated para-aramid yarns produced by an in-house developed electroless deposition method. In this paper we present our investigation on the yarn’s copper layer characteristics after deposition. Furthermore, we looked, in depth, at the yarn’s electro-conductive properties before and after washing as well as their mechanical properties before and after copper deposition. We found a dependency of the copper layer morphology on its deposition time. This is directly correlated to the resulting layer thickness and hence to the yarn’s electro-conductive properties, demonstrating the autocatalytic nature of the coating process. Above that, the electro-conductive properties of the coated yarn linearly decrease with washing cycles. Furthermore, the copper coating impairs the yarn’s mechanical properties decreasing its specific stress at break by 30%.
- Full Text:
- Date Issued: 2012
- Authors: Schwarz, Anne , Hakuzimana, Jean , Westbroek, Philippe , Mey, Gilbert De , Priniotakis, Georgios , Nyokong, Tebello , Langenhove, Lieva Van
- Date: 2012
- Subjects: To be catalogued
- Language: English
- Type: text , article
- Identifier: http://hdl.handle.net/10962/243487 , vital:51157 , xlink:href="https://doi.org/10.1177/0040517511431291"
- Description: The latest technological advances in new materials and devices enabled wearable systems to be created by utilizing textile solutions. These solutions require electro-conductive yarns as a basic component. Although the production of electroconductive yarn is widely reported, research is still necessary to characterize them to advance their electro-conductive and mechanical properties. Hence, we served this need and characterized copper-coated para-aramid yarns produced by an in-house developed electroless deposition method. In this paper we present our investigation on the yarn’s copper layer characteristics after deposition. Furthermore, we looked, in depth, at the yarn’s electro-conductive properties before and after washing as well as their mechanical properties before and after copper deposition. We found a dependency of the copper layer morphology on its deposition time. This is directly correlated to the resulting layer thickness and hence to the yarn’s electro-conductive properties, demonstrating the autocatalytic nature of the coating process. Above that, the electro-conductive properties of the coated yarn linearly decrease with washing cycles. Furthermore, the copper coating impairs the yarn’s mechanical properties decreasing its specific stress at break by 30%.
- Full Text:
- Date Issued: 2012
Comparative electrocatalytic behavior of self-assembled monolayer of thiol derivatised Co (II) phthalocyanines on gold disk, ultramicro cylinder and fiber electrodes
- Nombona, Nolwazi, Geraldo, Daniela A, Hakuzimana, Jean, Schwarz, Anne, Westbroek, Philippe, Nyokong, Tebello
- Authors: Nombona, Nolwazi , Geraldo, Daniela A , Hakuzimana, Jean , Schwarz, Anne , Westbroek, Philippe , Nyokong, Tebello
- Date: 2009
- Subjects: To be catalogued
- Language: English
- Type: text , article
- Identifier: http://hdl.handle.net/10962/263488 , vital:53632 , xlink:href="https://doi.org/10.1007/s10800-008-9716-y"
- Description: This paper reports on the use of thiol derivatised cobalt phthalocyanines as self assembled monolayers (SAMs) on gold disk electrode, gold ultramicro-cylinder electrode (UMCE) and on gold coated fiber for the detection of L-cysteine. The complexes are peripherally and non-peripherally substituted with phenylthio substituents. The SAM modified electrodes showed enhancement of catalytic currents and overpotential reduction occurred on the gold modified electrodes with different geometries. Electrocatalytic oxidation of L-cysteine on SAM modified gold coated fiber was reported for the first time. The gold coated fiber and ultramicro cylinder electrode were less stable towards the electrocatalytic oxidation of cysteine compared to its oxidation on the gold disk. The gold disk electrode gave better catalytic performance in terms of stability and reduction of overpotential.
- Full Text:
- Date Issued: 2009
- Authors: Nombona, Nolwazi , Geraldo, Daniela A , Hakuzimana, Jean , Schwarz, Anne , Westbroek, Philippe , Nyokong, Tebello
- Date: 2009
- Subjects: To be catalogued
- Language: English
- Type: text , article
- Identifier: http://hdl.handle.net/10962/263488 , vital:53632 , xlink:href="https://doi.org/10.1007/s10800-008-9716-y"
- Description: This paper reports on the use of thiol derivatised cobalt phthalocyanines as self assembled monolayers (SAMs) on gold disk electrode, gold ultramicro-cylinder electrode (UMCE) and on gold coated fiber for the detection of L-cysteine. The complexes are peripherally and non-peripherally substituted with phenylthio substituents. The SAM modified electrodes showed enhancement of catalytic currents and overpotential reduction occurred on the gold modified electrodes with different geometries. Electrocatalytic oxidation of L-cysteine on SAM modified gold coated fiber was reported for the first time. The gold coated fiber and ultramicro cylinder electrode were less stable towards the electrocatalytic oxidation of cysteine compared to its oxidation on the gold disk. The gold disk electrode gave better catalytic performance in terms of stability and reduction of overpotential.
- Full Text:
- Date Issued: 2009
Electroanalysis of thiocyanate using a novel glassy carbon electrode modified by aryl radicals and cobalt tetracarboxyphthalocyanine
- Matemadombo, Fungisai, Westbroek, Philippe, Nyokong, Tebello
- Authors: Matemadombo, Fungisai , Westbroek, Philippe , Nyokong, Tebello
- Date: 2007
- Subjects: To be catalogued
- Language: English
- Type: text , article
- Identifier: http://hdl.handle.net/10962/268750 , vital:54228 , xlink:href="https://doi.org/10.1016/j.electacta.2007.06.064"
- Description: Electrochemical grafting of 4-nitrobenzenediazonium tetrafluoroborate onto a glassy carbon electrode (GCE) results in the formation of a nitrophenyl radical, which reacts with the surface to form a covalent bond (grafting) and results in a nitrophenyl modified electrode. The nitro group is electrochemically reduced to a NH2 group. Cobalt tetracarboxyphthalocyanine (CoTCPc) complex is then attached to the NH2 group using 1-ethyl-3-(3-dimethylaminopropyl)-carbodiimide (EDC) and N-hydroxysuccinimide (NHS) as coupling agents. The new CoTCPc modified electrode was characterized using cyclic voltammetry and then employed for the catalytic oxidation of thiocyanate.
- Full Text:
- Date Issued: 2007
- Authors: Matemadombo, Fungisai , Westbroek, Philippe , Nyokong, Tebello
- Date: 2007
- Subjects: To be catalogued
- Language: English
- Type: text , article
- Identifier: http://hdl.handle.net/10962/268750 , vital:54228 , xlink:href="https://doi.org/10.1016/j.electacta.2007.06.064"
- Description: Electrochemical grafting of 4-nitrobenzenediazonium tetrafluoroborate onto a glassy carbon electrode (GCE) results in the formation of a nitrophenyl radical, which reacts with the surface to form a covalent bond (grafting) and results in a nitrophenyl modified electrode. The nitro group is electrochemically reduced to a NH2 group. Cobalt tetracarboxyphthalocyanine (CoTCPc) complex is then attached to the NH2 group using 1-ethyl-3-(3-dimethylaminopropyl)-carbodiimide (EDC) and N-hydroxysuccinimide (NHS) as coupling agents. The new CoTCPc modified electrode was characterized using cyclic voltammetry and then employed for the catalytic oxidation of thiocyanate.
- Full Text:
- Date Issued: 2007
Immobilization of tetra-amine substituted metallophthalocyanines at gold surfaces modified with mercaptopropionic acid or DTSP-SAMs
- Matemadombo, Fungisai, Westbroek, Philippe, Nyokong, Tebello, Ozoemena, Kenneth, De Clerck, Karen, Kiekens, Paul
- Authors: Matemadombo, Fungisai , Westbroek, Philippe , Nyokong, Tebello , Ozoemena, Kenneth , De Clerck, Karen , Kiekens, Paul
- Date: 2007
- Subjects: To be catalogued
- Language: English
- Type: text , article
- Identifier: http://hdl.handle.net/10962/283924 , vital:56003 , xlink:href="https://doi.org/10.1016/j.electacta.2006.08.027"
- Description: This paper shows that amine substituted cobalt phthalocyanine (CoTAPc) can be deposited on gold surfaces by using an interconnecting layer of a self-assembled monolayer (SAM) of mercaptopropionic acid or Lomant's reagent (dithiobis(N-succinimidyl propionate) (DTSP)). In both cases the new bond formed is obtained by the creation of an amide. The layers were characterized by electrochemistry and showed high coverage fractions (near 100%). Reductive and oxidative desorption of the SAMs limit the useful potential window from −0.6 to +0.5 V versus Ag|AgCl. The SAM-CoTAPc layers show electrocatalytic activities towards oxygen reduction through the Co(I) central metal ion. The amount of CoTAPc molecules deposited (obtained from the Co central metal ion activity in nitrogen purged solutions) revealed that the CoTAPc molecules are bonded in a perpendicular manner at the surface. Taking into account a surface of 200 Å2 for a flatly bonded MPc, this should result in a four times less amount of deposited CoTAPc compared to the experimental value obtained. Both methods showed good results and promising long-term stability and will be interesting tools for further research in surface modification and sensor development.
- Full Text:
- Date Issued: 2007
- Authors: Matemadombo, Fungisai , Westbroek, Philippe , Nyokong, Tebello , Ozoemena, Kenneth , De Clerck, Karen , Kiekens, Paul
- Date: 2007
- Subjects: To be catalogued
- Language: English
- Type: text , article
- Identifier: http://hdl.handle.net/10962/283924 , vital:56003 , xlink:href="https://doi.org/10.1016/j.electacta.2006.08.027"
- Description: This paper shows that amine substituted cobalt phthalocyanine (CoTAPc) can be deposited on gold surfaces by using an interconnecting layer of a self-assembled monolayer (SAM) of mercaptopropionic acid or Lomant's reagent (dithiobis(N-succinimidyl propionate) (DTSP)). In both cases the new bond formed is obtained by the creation of an amide. The layers were characterized by electrochemistry and showed high coverage fractions (near 100%). Reductive and oxidative desorption of the SAMs limit the useful potential window from −0.6 to +0.5 V versus Ag|AgCl. The SAM-CoTAPc layers show electrocatalytic activities towards oxygen reduction through the Co(I) central metal ion. The amount of CoTAPc molecules deposited (obtained from the Co central metal ion activity in nitrogen purged solutions) revealed that the CoTAPc molecules are bonded in a perpendicular manner at the surface. Taking into account a surface of 200 Å2 for a flatly bonded MPc, this should result in a four times less amount of deposited CoTAPc compared to the experimental value obtained. Both methods showed good results and promising long-term stability and will be interesting tools for further research in surface modification and sensor development.
- Full Text:
- Date Issued: 2007
Surface chemistry and electrocatalytic behaviour of tetra-carboxy substituted iron, cobalt and manganese phthalocyanine monolayers on gold electrode
- Mashazi, Philani N, Westbroek, Philippe, Ozoemena, Kenneth I, Nyokong, Tebello
- Authors: Mashazi, Philani N , Westbroek, Philippe , Ozoemena, Kenneth I , Nyokong, Tebello
- Date: 2007
- Subjects: To be catalogued
- Language: English
- Type: text , article
- Identifier: http://hdl.handle.net/10962/268806 , vital:54233 , xlink:href="https://doi.org/10.1016/j.electacta.2007.08.044"
- Description: Surface chemistry and electrocatalytic properties of self-assembled monolayers of metal tetra-carboxylic acid phthalocyanine complexes with cobalt (Co), iron (Fe) and manganese (Mn) as central metal ions have been studied. These phthalocyanine molecules are immobilized on gold electrode via the coupling reaction between the ring substituents and pre-formed mercaptoethanol self-assembled monolayer (Au-ME SAM). X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy confirmed chemisorption of mercaptoethanol via sulfur group on gold electrode and also coupling reaction between phthalocyanines and Au-ME SAM. Electrochemical parameters of the immobilized molecules show that these molecules are densely packed with a perpendicular orientation. The potential applications of the gold modified electrodes were investigated towards L-cysteine detection and the analysis at phthalocyanine SAMs. Cobalt and iron tetra-carboxylic acid phthalocyanine monolayers showed good oxidation peak for L-cysteine at potentials where metal oxidation (MIII/MII) takes place and this metal oxidation mediates the catalytic oxidation of L-cysteine. Manganese tetra-carboxylic acid phthalocyanine monolayer also exhibited a good catalytic oxidation peak towards L-cysteine at potentials where MnIV/MnIII redox peak occurs and this redox peak mediates L-cysteine oxidation. The analysis of cysteine at phthalocyanine monolayers displayed good analytical parameters with good detection limits of the orders of 10−7 mol L−1 and good linearity for a studied concentration range up to 60 μmol L−1.
- Full Text:
- Date Issued: 2007
- Authors: Mashazi, Philani N , Westbroek, Philippe , Ozoemena, Kenneth I , Nyokong, Tebello
- Date: 2007
- Subjects: To be catalogued
- Language: English
- Type: text , article
- Identifier: http://hdl.handle.net/10962/268806 , vital:54233 , xlink:href="https://doi.org/10.1016/j.electacta.2007.08.044"
- Description: Surface chemistry and electrocatalytic properties of self-assembled monolayers of metal tetra-carboxylic acid phthalocyanine complexes with cobalt (Co), iron (Fe) and manganese (Mn) as central metal ions have been studied. These phthalocyanine molecules are immobilized on gold electrode via the coupling reaction between the ring substituents and pre-formed mercaptoethanol self-assembled monolayer (Au-ME SAM). X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy confirmed chemisorption of mercaptoethanol via sulfur group on gold electrode and also coupling reaction between phthalocyanines and Au-ME SAM. Electrochemical parameters of the immobilized molecules show that these molecules are densely packed with a perpendicular orientation. The potential applications of the gold modified electrodes were investigated towards L-cysteine detection and the analysis at phthalocyanine SAMs. Cobalt and iron tetra-carboxylic acid phthalocyanine monolayers showed good oxidation peak for L-cysteine at potentials where metal oxidation (MIII/MII) takes place and this metal oxidation mediates the catalytic oxidation of L-cysteine. Manganese tetra-carboxylic acid phthalocyanine monolayer also exhibited a good catalytic oxidation peak towards L-cysteine at potentials where MnIV/MnIII redox peak occurs and this redox peak mediates L-cysteine oxidation. The analysis of cysteine at phthalocyanine monolayers displayed good analytical parameters with good detection limits of the orders of 10−7 mol L−1 and good linearity for a studied concentration range up to 60 μmol L−1.
- Full Text:
- Date Issued: 2007
Synthesis and electrochemical properties of benzyl-mercapto and dodecyl-mercapto tetrasubstituted manganese phthalocyanine complexes
- Agboola, Bolade, Ozoemena, Kenneth I, Westbroek, Philippe, Nyokong, Tebello
- Authors: Agboola, Bolade , Ozoemena, Kenneth I , Westbroek, Philippe , Nyokong, Tebello
- Date: 2007
- Subjects: To be catalogued
- Language: English
- Type: text , article
- Identifier: http://hdl.handle.net/10962/281321 , vital:55713 , xlink:href="https://doi.org/10.1016/j.electacta.2006.09.002"
- Description: Manganese tetrakis (benzyl-mercapto) phthalocyanine (MnTBMPc) and manganese tetrakis (dodecyl-mercapto) phthalocyanine (MnTDMPc) complexes were synthesized and their spectral and electrochemical properties are reported. Cyclic voltammetric data showed three reversible to quasi-reversible and two irreversible redox processes for both complexes. Ring substituents influenced the positions of both oxidation and reduction redox couples. Spectroelectrochemistry confirmed the first two reductions to be due to MnIIIPc2−/MnIIPc2− and MnIIPc3−/MnIIPc2− processes. The first example of a formation of self-assembled monolayers (SAMs) using thiol substituted MnPc complexes is presented, the SAMs were found to show blocking characteristics towards some faradaic reactions.
- Full Text:
- Date Issued: 2007
- Authors: Agboola, Bolade , Ozoemena, Kenneth I , Westbroek, Philippe , Nyokong, Tebello
- Date: 2007
- Subjects: To be catalogued
- Language: English
- Type: text , article
- Identifier: http://hdl.handle.net/10962/281321 , vital:55713 , xlink:href="https://doi.org/10.1016/j.electacta.2006.09.002"
- Description: Manganese tetrakis (benzyl-mercapto) phthalocyanine (MnTBMPc) and manganese tetrakis (dodecyl-mercapto) phthalocyanine (MnTDMPc) complexes were synthesized and their spectral and electrochemical properties are reported. Cyclic voltammetric data showed three reversible to quasi-reversible and two irreversible redox processes for both complexes. Ring substituents influenced the positions of both oxidation and reduction redox couples. Spectroelectrochemistry confirmed the first two reductions to be due to MnIIIPc2−/MnIIPc2− and MnIIPc3−/MnIIPc2− processes. The first example of a formation of self-assembled monolayers (SAMs) using thiol substituted MnPc complexes is presented, the SAMs were found to show blocking characteristics towards some faradaic reactions.
- Full Text:
- Date Issued: 2007
Voltammetric characterisation of the self-assembled monolayers (SAMs) of benzyl-and dodecyl-mercapto tetra substituted metallophthalocyanines complexes
- Agboola, Bolade, Westbroek, Philippe, Ozoemena, Kenneth I, Nyokong, Tebello
- Authors: Agboola, Bolade , Westbroek, Philippe , Ozoemena, Kenneth I , Nyokong, Tebello
- Date: 2007
- Subjects: To be catalogued
- Language: English
- Type: text , article
- Identifier: http://hdl.handle.net/10962/281414 , vital:55723 , xlink:href="https://doi.org/10.1016/j.elecom.2006.08.047"
- Description: Voltammetric characterisations of cobalt, iron, manganese, nickel and zinc phthalocyanine complexes tetra substituted with benzyl- and dodecyl-mercapto ring substituents and immobilisation on gold electrodes via the self-assembling technique are presented. The self-assembled films are stable and showed blocking characteristics towards the following Faradaic processes; gold surface oxidation, under potential deposition of copper and solution redox chemistry of [Fe(H2O)6 3+ ]/[Fe(H2O)6 2+ ]. The solution chemistry of [Fe(CN)6]−3/[Fe(CN)6]−4 redox process was used to study the orientation of the CoPcs-SAMs and this revealed a possible deviation from flat orientation of the complexes on the gold electrodes when the SAM formation times were greater than 24 h. For SAM formation time at 24 and 48 h, CoTDMPc-SAM showed more inhibition of the [Fe(CN)6]−3/[Fe(CN)6]−4 redox process than the CoTBMPc-SAM counterpart, indicating more blocking characteristics of the dodecylmercapto ring substituents compared to the benzylmercapto counterpart. To avoid SAM desorption, the potential application should be limited to −0.2 to +0.8 V vs. Ag∣AgCl (NaCl, sat’d) in acidic and neutral pH.
- Full Text:
- Date Issued: 2007
- Authors: Agboola, Bolade , Westbroek, Philippe , Ozoemena, Kenneth I , Nyokong, Tebello
- Date: 2007
- Subjects: To be catalogued
- Language: English
- Type: text , article
- Identifier: http://hdl.handle.net/10962/281414 , vital:55723 , xlink:href="https://doi.org/10.1016/j.elecom.2006.08.047"
- Description: Voltammetric characterisations of cobalt, iron, manganese, nickel and zinc phthalocyanine complexes tetra substituted with benzyl- and dodecyl-mercapto ring substituents and immobilisation on gold electrodes via the self-assembling technique are presented. The self-assembled films are stable and showed blocking characteristics towards the following Faradaic processes; gold surface oxidation, under potential deposition of copper and solution redox chemistry of [Fe(H2O)6 3+ ]/[Fe(H2O)6 2+ ]. The solution chemistry of [Fe(CN)6]−3/[Fe(CN)6]−4 redox process was used to study the orientation of the CoPcs-SAMs and this revealed a possible deviation from flat orientation of the complexes on the gold electrodes when the SAM formation times were greater than 24 h. For SAM formation time at 24 and 48 h, CoTDMPc-SAM showed more inhibition of the [Fe(CN)6]−3/[Fe(CN)6]−4 redox process than the CoTBMPc-SAM counterpart, indicating more blocking characteristics of the dodecylmercapto ring substituents compared to the benzylmercapto counterpart. To avoid SAM desorption, the potential application should be limited to −0.2 to +0.8 V vs. Ag∣AgCl (NaCl, sat’d) in acidic and neutral pH.
- Full Text:
- Date Issued: 2007
Electrochemical behavior and detection of dopamine and ascorbic acid at an iron (II) tetrasulfophthalocyanine modified carbon paste microelectrode
- Oni, Joshua, Westbroek, Philippe, Nyokong, Tebello
- Authors: Oni, Joshua , Westbroek, Philippe , Nyokong, Tebello
- Date: 2003
- Subjects: To be catalogued
- Language: English
- Type: text , article
- Identifier: http://hdl.handle.net/10962/290279 , vital:56735 , xlink:href="https://doi.org/10.1002/elan.200390104"
- Description: In this article the electrocatalytic behavior of an iron(II)tetrasulfophthalocyanine modified carbon paste microelectrode for the oxidation of dopamine (DA) and ascorbic acid (AA) is described. Although the oxidation potential of ascorbic acid is shifted by over 100 mV to more positive potentials, no peak separation could be obtained. This can be explained by the immediate homogeneous reduction of the oxidation product of dopamine by ascorbic acid in solution. However, this reaction induces a shift of the half-wave potential as a function of ratio of concentration of dopamine to ascorbic acid (cDA/cAA). Therefore it was possible to determine the cAA and cDA from this potential shift and the experimental peak current. Detection limits of 4.5±0.2×10−7 and 7.5±0.5×10−7 mol L−1 were obtained respectively for dopamine and ascorbic acid for cDA/cAA>0.01.
- Full Text:
- Date Issued: 2003
- Authors: Oni, Joshua , Westbroek, Philippe , Nyokong, Tebello
- Date: 2003
- Subjects: To be catalogued
- Language: English
- Type: text , article
- Identifier: http://hdl.handle.net/10962/290279 , vital:56735 , xlink:href="https://doi.org/10.1002/elan.200390104"
- Description: In this article the electrocatalytic behavior of an iron(II)tetrasulfophthalocyanine modified carbon paste microelectrode for the oxidation of dopamine (DA) and ascorbic acid (AA) is described. Although the oxidation potential of ascorbic acid is shifted by over 100 mV to more positive potentials, no peak separation could be obtained. This can be explained by the immediate homogeneous reduction of the oxidation product of dopamine by ascorbic acid in solution. However, this reaction induces a shift of the half-wave potential as a function of ratio of concentration of dopamine to ascorbic acid (cDA/cAA). Therefore it was possible to determine the cAA and cDA from this potential shift and the experimental peak current. Detection limits of 4.5±0.2×10−7 and 7.5±0.5×10−7 mol L−1 were obtained respectively for dopamine and ascorbic acid for cDA/cAA>0.01.
- Full Text:
- Date Issued: 2003
Self-Assembled Monolayers of Cobalt and Iron Phthalocyanine Complexes on Gold Electrodes
- Ozoemena, Kenneth I, Nyokong, Tebello, Westbroek, Philippe
- Authors: Ozoemena, Kenneth I , Nyokong, Tebello , Westbroek, Philippe
- Date: 2003
- Subjects: To be catalogued
- Language: English
- Type: text , article
- Identifier: http://hdl.handle.net/10962/290363 , vital:56743 , xlink:href="https://doi.org/10.1002/elan.200302753"
- Description: The self-assembling of the octa(hydroxyethylthio)-metallophthalocyanine {MOHETPc (M=Co and Fe)} complexes and their similar analogues, octabutylthiometallophthalocyanine {MOBTPc (M=Co and Fe)} complexes on gold electrodes are investigated. Comparative surface voltammetric insights into their distinct self-assembling properties with respect to the passivation of Faradaic processes and surface coverages, including their solution electrochemistry, suggest different orientations and non-cleavage of their CS bonds. In the pH 2−9 range, the reversible [M(III)Pc(−2)]+ / [M(II)Pc(−2)] redox couples show potential shifts close to −59 mV / pH. The gold electrodes modified with the SAMs of these species show electrocatalytic activity towards the oxidation of thiols (L-cysteine, homocysteine and penicillamine) and thiocyanate in acidic media with detection limits in the region of 10−7–10−6 mol dm−3. These monolayers are stable and easily reproducible.
- Full Text:
- Date Issued: 2003
- Authors: Ozoemena, Kenneth I , Nyokong, Tebello , Westbroek, Philippe
- Date: 2003
- Subjects: To be catalogued
- Language: English
- Type: text , article
- Identifier: http://hdl.handle.net/10962/290363 , vital:56743 , xlink:href="https://doi.org/10.1002/elan.200302753"
- Description: The self-assembling of the octa(hydroxyethylthio)-metallophthalocyanine {MOHETPc (M=Co and Fe)} complexes and their similar analogues, octabutylthiometallophthalocyanine {MOBTPc (M=Co and Fe)} complexes on gold electrodes are investigated. Comparative surface voltammetric insights into their distinct self-assembling properties with respect to the passivation of Faradaic processes and surface coverages, including their solution electrochemistry, suggest different orientations and non-cleavage of their CS bonds. In the pH 2−9 range, the reversible [M(III)Pc(−2)]+ / [M(II)Pc(−2)] redox couples show potential shifts close to −59 mV / pH. The gold electrodes modified with the SAMs of these species show electrocatalytic activity towards the oxidation of thiols (L-cysteine, homocysteine and penicillamine) and thiocyanate in acidic media with detection limits in the region of 10−7–10−6 mol dm−3. These monolayers are stable and easily reproducible.
- Full Text:
- Date Issued: 2003
Cyclic voltammetric studies of octabutylthiophthalo-cyaninato-cobalt (II) and its self-assembled monolayer (SAM) on gold electrode
- Ozoemena, Kenneth, Westbroek, Philippe, Nyokong, Tebello
- Authors: Ozoemena, Kenneth , Westbroek, Philippe , Nyokong, Tebello
- Date: 2002
- Subjects: To be catalogued
- Language: English
- Type: text , article
- Identifier: http://hdl.handle.net/10962/289567 , vital:56650 , xlink:href="https://doi.org/10.1142/S1088424602000130"
- Description: The synthesis of thiol-derivatized cobalt phthalocyanine complex, 2,3,9,10,16,17,23,24-octa (butylthiophthalocyaninatocobalt(II) (CoOBTPc) is described. Cyclic voltammetric data of this complex in DMF showed five quasi-reversible and reversible, diffusion-controlled redox couples, comprising both the phthalocyanine ring and central metal redox processes. The CoOBTPc complex forms a self-assembled monolayer (SAM) on gold electrode. The investigation of the integrity of this SAM, using the established cyclic voltammetric methods in aqueous alkaline solutions, gave evidence about the formation of a stable and easily reproducible monolayer. However, due to its susceptibility to destruction via oxidative and reductive desorptions, its potential application as an electrochemical sensor in alkaline pH is limited to a potential window of between −0.20 and +0.55 V vs Ag/AgCl.
- Full Text:
- Date Issued: 2002
- Authors: Ozoemena, Kenneth , Westbroek, Philippe , Nyokong, Tebello
- Date: 2002
- Subjects: To be catalogued
- Language: English
- Type: text , article
- Identifier: http://hdl.handle.net/10962/289567 , vital:56650 , xlink:href="https://doi.org/10.1142/S1088424602000130"
- Description: The synthesis of thiol-derivatized cobalt phthalocyanine complex, 2,3,9,10,16,17,23,24-octa (butylthiophthalocyaninatocobalt(II) (CoOBTPc) is described. Cyclic voltammetric data of this complex in DMF showed five quasi-reversible and reversible, diffusion-controlled redox couples, comprising both the phthalocyanine ring and central metal redox processes. The CoOBTPc complex forms a self-assembled monolayer (SAM) on gold electrode. The investigation of the integrity of this SAM, using the established cyclic voltammetric methods in aqueous alkaline solutions, gave evidence about the formation of a stable and easily reproducible monolayer. However, due to its susceptibility to destruction via oxidative and reductive desorptions, its potential application as an electrochemical sensor in alkaline pH is limited to a potential window of between −0.20 and +0.55 V vs Ag/AgCl.
- Full Text:
- Date Issued: 2002
pH study of the electrocatalytic SO2 detection at a glassy carbon electrode modified with iron (II) tetrasulfophthalocyanine
- Thamae, Mamothibe, Westbroek, Philippe, Nyokong, Tebello
- Authors: Thamae, Mamothibe , Westbroek, Philippe , Nyokong, Tebello
- Date: 2002
- Subjects: To be catalogued
- Language: English
- Type: text , article
- Identifier: http://hdl.handle.net/10962/304786 , vital:58490 , xlink:href="https://doi.org/10.1007/s00604-002-0914-8"
- Description: The electrocatalytic determination of SO2 is studied as a function of pH at a glassy carbon electrode modified with iron(II)tetrasulfophthalocyanine ([Fe(II)TSPc]4−). It was found in the literature that depending on pH, SO2·xH2O, HSO3 − and/or SO3 2− are the main compounds in solution, that these compounds behave differently at the electrode surface, and that the condition of the electrode surface is stable over the entire pH-range. The use of SO2(g) or sodium sulfite as starting material did result in identical curves except in the pH range from 7.5–9.0. A possible explanation could be given by proposing that SO2·xH2O is very unstable in the presence of SO3 2−. In strongly acidic medium, SO2·xH2O is the main compound, which can be oxidized as well as reduced with exchange of two electrons. HSO3 − is the main compound at pH = 4 and can also be oxidized and reduced with exchange of, respectively, two and four electrons. In alkaline solution sulfite is the main compound and can only be oxidized, also under exchange of two electrons. Detection limits are in the range of 4.0 ± 0.1 × 10−5 and 7.5 ± 0.1 × 10−5 mol L−1, dependent of pH and of the type of reaction (oxidation or reduction) used.
- Full Text:
- Date Issued: 2002
- Authors: Thamae, Mamothibe , Westbroek, Philippe , Nyokong, Tebello
- Date: 2002
- Subjects: To be catalogued
- Language: English
- Type: text , article
- Identifier: http://hdl.handle.net/10962/304786 , vital:58490 , xlink:href="https://doi.org/10.1007/s00604-002-0914-8"
- Description: The electrocatalytic determination of SO2 is studied as a function of pH at a glassy carbon electrode modified with iron(II)tetrasulfophthalocyanine ([Fe(II)TSPc]4−). It was found in the literature that depending on pH, SO2·xH2O, HSO3 − and/or SO3 2− are the main compounds in solution, that these compounds behave differently at the electrode surface, and that the condition of the electrode surface is stable over the entire pH-range. The use of SO2(g) or sodium sulfite as starting material did result in identical curves except in the pH range from 7.5–9.0. A possible explanation could be given by proposing that SO2·xH2O is very unstable in the presence of SO3 2−. In strongly acidic medium, SO2·xH2O is the main compound, which can be oxidized as well as reduced with exchange of two electrons. HSO3 − is the main compound at pH = 4 and can also be oxidized and reduced with exchange of, respectively, two and four electrons. In alkaline solution sulfite is the main compound and can only be oxidized, also under exchange of two electrons. Detection limits are in the range of 4.0 ± 0.1 × 10−5 and 7.5 ± 0.1 × 10−5 mol L−1, dependent of pH and of the type of reaction (oxidation or reduction) used.
- Full Text:
- Date Issued: 2002
Voltammetric detection of vitamin B1 at carbon paste electrodes and its determination in tablets
- Oni, Joshua, Westbroek, Philippe, Nyokong, Tebello
- Authors: Oni, Joshua , Westbroek, Philippe , Nyokong, Tebello
- Date: 2002
- Subjects: To be catalogued
- Language: English
- Type: text , article
- Identifier: http://hdl.handle.net/10962/289692 , vital:56663 , xlink:href="https://doi.org/10.1002/1521-4109(200209)14"
- Description: The voltammetric behavior of vitamin B1 in alkaline medium at carbon paste electrode (CPE) is discussed. A method based on cyclic voltammetry for the determination of vitamin B1 at carbon paste electrode modified with manganese phthalocyanine (MnPc-CPE) is presented. In pH 10 buffer, the modified electrode showed catalytic activity towards the oxidation of vitamin B1 by considerably increasing the oxidation current of one of the observed waves compared to the oxidation current obtained at an unmodified electrode. The modified electrode was stable towards the determination of vitamin B1 compared to the unmodified electrode that is completely poisoned after a few scans. A linear relationship between the oxidation current and the concentration of vitamin B1 in solution was observed. The detection limit for vitamin B1 at the modified electrode was of the order of 10−5 mol dm−3. Commercial vitamin B1 tablets were analyzed using the modified electrodes.
- Full Text:
- Date Issued: 2002
- Authors: Oni, Joshua , Westbroek, Philippe , Nyokong, Tebello
- Date: 2002
- Subjects: To be catalogued
- Language: English
- Type: text , article
- Identifier: http://hdl.handle.net/10962/289692 , vital:56663 , xlink:href="https://doi.org/10.1002/1521-4109(200209)14"
- Description: The voltammetric behavior of vitamin B1 in alkaline medium at carbon paste electrode (CPE) is discussed. A method based on cyclic voltammetry for the determination of vitamin B1 at carbon paste electrode modified with manganese phthalocyanine (MnPc-CPE) is presented. In pH 10 buffer, the modified electrode showed catalytic activity towards the oxidation of vitamin B1 by considerably increasing the oxidation current of one of the observed waves compared to the oxidation current obtained at an unmodified electrode. The modified electrode was stable towards the determination of vitamin B1 compared to the unmodified electrode that is completely poisoned after a few scans. A linear relationship between the oxidation current and the concentration of vitamin B1 in solution was observed. The detection limit for vitamin B1 at the modified electrode was of the order of 10−5 mol dm−3. Commercial vitamin B1 tablets were analyzed using the modified electrodes.
- Full Text:
- Date Issued: 2002
Voltammetric detection of vitamin B1 at carbon paste electrodes and its determination in tablets
- Oni, Joshua, Westbroek, Philippe, Nyokong, Tebello
- Authors: Oni, Joshua , Westbroek, Philippe , Nyokong, Tebello
- Date: 2002
- Subjects: To be catalogued
- Language: English
- Type: text , article
- Identifier: http://hdl.handle.net/10962/289678 , vital:56662 , xlink:href="https://doi.org/10.1002/1521-4109(200209)14"
- Description: The voltammetric behavior of vitamin B1 in alkaline medium at carbon paste electrode (CPE) is discussed. A method based on cyclic voltammetry for the determination of vitamin B1 at carbon paste electrode modified with manganese phthalocyanine (MnPc-CPE) is presented. In pH 10 buffer, the modified electrode showed catalytic activity towards the oxidation of vitamin B1 by considerably increasing the oxidation current of one of the observed waves compared to the oxidation current obtained at an unmodified electrode. The modified electrode was stable towards the determination of vitamin B1 compared to the unmodified electrode that is completely poisoned after a few scans. A linear relationship between the oxidation current and the concentration of vitamin B1 in solution was observed. The detection limit for vitamin B1 at the modified electrode was of the order of 10−5 mol dm−3. Commercial vitamin B1 tablets were analyzed using the modified electrodes.
- Full Text:
- Date Issued: 2002
- Authors: Oni, Joshua , Westbroek, Philippe , Nyokong, Tebello
- Date: 2002
- Subjects: To be catalogued
- Language: English
- Type: text , article
- Identifier: http://hdl.handle.net/10962/289678 , vital:56662 , xlink:href="https://doi.org/10.1002/1521-4109(200209)14"
- Description: The voltammetric behavior of vitamin B1 in alkaline medium at carbon paste electrode (CPE) is discussed. A method based on cyclic voltammetry for the determination of vitamin B1 at carbon paste electrode modified with manganese phthalocyanine (MnPc-CPE) is presented. In pH 10 buffer, the modified electrode showed catalytic activity towards the oxidation of vitamin B1 by considerably increasing the oxidation current of one of the observed waves compared to the oxidation current obtained at an unmodified electrode. The modified electrode was stable towards the determination of vitamin B1 compared to the unmodified electrode that is completely poisoned after a few scans. A linear relationship between the oxidation current and the concentration of vitamin B1 in solution was observed. The detection limit for vitamin B1 at the modified electrode was of the order of 10−5 mol dm−3. Commercial vitamin B1 tablets were analyzed using the modified electrodes.
- Full Text:
- Date Issued: 2002
Construction and characterization of carbon paste ultra-microelectrodes
- Oni, Joshua, Westbroek, Philippe, Nyokong, Tebello
- Authors: Oni, Joshua , Westbroek, Philippe , Nyokong, Tebello
- Date: 2001
- Subjects: To be catalogued
- Language: English
- Type: text , article
- Identifier: http://hdl.handle.net/10962/291531 , vital:56884 , xlink:href="https://doi.org/10.1016/S1388-2481(01)00212-0"
- Description: The construction and characterization of carbon paste ultra-microelectrodes is reported. Besides a disc-shaped electrode, a carbon paste band electrode is studied. It was found that for both electrode configurations steady-state currents were obtained but that with the type of electrode material used for the band electrode, the upper limit of ultra-microelectrode dimensions, which could be used was 100–150 μm. Smaller dimensions for the band electrodes resulted in a high resistance due to the limited conductivity of the carbon paste, when using the optimal paste composition. With cyclic voltammetry, the oxidation of [Fe(CN)6]4− was studied at individual constructed electrodes and at ensembles of individual electrodes. Detection limits of less than 10−6moll−1 were obtained. Using the data of the same curves it was possible to test if the electrodes have errors and about 20% of the constructed electrodes did not pass this test. Finally it was found that these electrodes show good stability.
- Full Text:
- Date Issued: 2001
- Authors: Oni, Joshua , Westbroek, Philippe , Nyokong, Tebello
- Date: 2001
- Subjects: To be catalogued
- Language: English
- Type: text , article
- Identifier: http://hdl.handle.net/10962/291531 , vital:56884 , xlink:href="https://doi.org/10.1016/S1388-2481(01)00212-0"
- Description: The construction and characterization of carbon paste ultra-microelectrodes is reported. Besides a disc-shaped electrode, a carbon paste band electrode is studied. It was found that for both electrode configurations steady-state currents were obtained but that with the type of electrode material used for the band electrode, the upper limit of ultra-microelectrode dimensions, which could be used was 100–150 μm. Smaller dimensions for the band electrodes resulted in a high resistance due to the limited conductivity of the carbon paste, when using the optimal paste composition. With cyclic voltammetry, the oxidation of [Fe(CN)6]4− was studied at individual constructed electrodes and at ensembles of individual electrodes. Detection limits of less than 10−6moll−1 were obtained. Using the data of the same curves it was possible to test if the electrodes have errors and about 20% of the constructed electrodes did not pass this test. Finally it was found that these electrodes show good stability.
- Full Text:
- Date Issued: 2001
Photodynamic inactivation of Staphylococcus aureus using low symmetrically substituted phthalocyanines supported on a polystyrene polymer fiber
- Masilela, Nkosiphile, Kleyi, Phumelele, Tshentu, Zenixole R, Priniotakis, Georgios, Westbroek, Philippe, Nyokong, Tebello
- Authors: Masilela, Nkosiphile , Kleyi, Phumelele , Tshentu, Zenixole R , Priniotakis, Georgios , Westbroek, Philippe , Nyokong, Tebello
- Language: English
- Type: Article
- Identifier: vital:7330 , http://hdl.handle.net/10962/d1020591
- Description: This work reports on the antimicrobial photo-activities of a series of low symmetrically substituted phthalocyanine complexes in solution and in a fiber matrix. Phthalocyanine complexes were successfully electrospun into a polystyrene polymer. The fiber diameter ranged from 240 nm to 390 nm in average. The modified polymer fiber showed successful singlet oxygen production with the Ge monocarboxy phthalocyanine modified fiber giving the highest singlet oxygen quantum yield value of 0.46 due to lack of aggregation when in the polymer. All the unsymmetrically substituted complexes showed antimicrobial activity towards S. Aureus under illumination with visible light. The symmetrical ZnPc and ZnTPCPc showed no activity under illumination with light in the fiber matrix due to low singlet oxygen production. , Original publication is available at http://dx.doi.org/10.1016/j.dyepig.2012.10.001
- Full Text: false
- Authors: Masilela, Nkosiphile , Kleyi, Phumelele , Tshentu, Zenixole R , Priniotakis, Georgios , Westbroek, Philippe , Nyokong, Tebello
- Language: English
- Type: Article
- Identifier: vital:7330 , http://hdl.handle.net/10962/d1020591
- Description: This work reports on the antimicrobial photo-activities of a series of low symmetrically substituted phthalocyanine complexes in solution and in a fiber matrix. Phthalocyanine complexes were successfully electrospun into a polystyrene polymer. The fiber diameter ranged from 240 nm to 390 nm in average. The modified polymer fiber showed successful singlet oxygen production with the Ge monocarboxy phthalocyanine modified fiber giving the highest singlet oxygen quantum yield value of 0.46 due to lack of aggregation when in the polymer. All the unsymmetrically substituted complexes showed antimicrobial activity towards S. Aureus under illumination with visible light. The symmetrical ZnPc and ZnTPCPc showed no activity under illumination with light in the fiber matrix due to low singlet oxygen production. , Original publication is available at http://dx.doi.org/10.1016/j.dyepig.2012.10.001
- Full Text: false
- «
- ‹
- 1
- ›
- »