Comparative performance of 3-kWp ranges Solar Photovoltaic Systems under varying meteorological conditions in Alice, Eastern Cape Province, South Africa
- Apeh, Oliver Okechukwu https://orcid.org/0000-0003-4076-0613
- Authors: Apeh, Oliver Okechukwu https://orcid.org/0000-0003-4076-0613
- Date: 2021-08
- Subjects: Photovoltaic power systems , Solar energy
- Language: English
- Type: Doctoral theses , text
- Identifier: http://hdl.handle.net/10353/21567 , vital:48888
- Description: PVsystem has recently emerged in South Africa as a way to curb the country’s persistent shortage of electricity. A wide effort for the past few decades have targeted at study, testing and demonstration of PV power systems which was established all over the country as an appropriate measure to tackle transportation, agriculture, industry, commercial as well as domestic activities. In view of these drives, both off-grid and grid-connected PV systems are being applied. However, operating a building with an off-grid system is one of the means to providing the possibility of energy access to places far away from the national grid. As an off-grid choice, 50 W SHS is being distributed to customers in distant rustic parts of the country where grid option is difficult to access. But the SHS of the stated capacity can barely generate 0.3 to 0.4 kWh of electric energy per day, even at the optimal solar radiations. In view of this, more efforts are directed at expanding the off-grid systems to accommodate large rural households in South Africa. This thesis is dedicated to a study on the various configurations and components of PV power plant as a way to enhance electricity generations in South Africa. To this effect, different power plants were considered at SolarWatt park, University of Fort Hare with the aim to conduct a comparative analysis of the charge controllers with respect to the charge and discharge rates of their respective batteries. The grid-connected PV power generation was classified into hybrid PV and grid-assisted PV, while off-grid is a BIPV. These power plants generations were installed for the purpose of research level with a total capacity of 11.4 kW. The off-grid system is made up of HIT modules, FlexMax80 charge controller, Victron energy inverter and M-Molar battery bank. The hybrid and grid-assisted systems each consist of 15 polycrystalline modules and Microcare charge controllers. In addition, hybrid comprises SMA Sunny Island inverter and Trojan battery bank whereas grid-assisted consist of Microcare inverter and Hoppercke battery bank. The first part of the experimental work was monitored, and the meteorological parameters which are ambient temperature, solar radiation, relative humidity and wind speed, were measured and evaluated while electrical parameters includes PV current and voltage, MPPT current and voltage, battery current and voltage and inverter current and voltage were also measured and evaluated in the second part of the experiment. This lasted for a period of four years, starting from 1st January 2017 to 31st December 2020. Similarly, the second aspect was to monitor the electrical performance of the three systems and was performed for a period of six months, starting from January to June 2019. During the second experiment, hybrid and grid-assisted systems were reconfigured to function as off-grid systems. Moreover, a detailed data acquisition system designed to measure and record both meteorological and electrical parameters affecting the performance of the systems. The electrical parameters include PV current and voltage, MPPT current, battery current and voltage and inverter current and voltage. Other parameters in the measurements are; inverter efficiency, active and apparent power, while meteorological parameters include; solar irradiance, ambient temperature, relative humidity, wind speed and direction. The meteorological results show that the maximum and minimum mean amount of global solar radiation was 7.34 kWh/m2/day in December and 3.03 kWh/m2/day in June, respectively, while the average radiation and temperature for the typical year were 4.98 kWh/m2/day and 16.88 oC respectively. The solar radiations obtained are within the range in major places in South Africa. Similarly, an average wind speed of 2.5 m/s is experienced in Alice in a year and average solar radiation of 606.06 W/m2 in summer and 346.17 W/m2 in winter. The three lead-acid battery systems monitored under the electrical aspect are M-Molar, Trojan and Hoppecke battery systems. It was established that the charging current decreases gradually from 27.7 to 18.5 A for the M-Molar while Hoppecke and Trojan deceased respectively from 15 to 10 A and 23 to 13 A at the end of each phase by charging it at the maximum power point of the PV array. It was equally found that the M-Molar battery current has the highest rate of charging and quickest rate of discharging in comparison to the other two batteries. Finally, from the results gotten from this research, we may propose that the solar PV system contributes significantly to the satisfaction of the needed electricity in South Africa. , Thesis (PhD) -- Faculty of Science and Agriculture, 2021
- Full Text:
- Date Issued: 2021-08
- Authors: Apeh, Oliver Okechukwu https://orcid.org/0000-0003-4076-0613
- Date: 2021-08
- Subjects: Photovoltaic power systems , Solar energy
- Language: English
- Type: Doctoral theses , text
- Identifier: http://hdl.handle.net/10353/21567 , vital:48888
- Description: PVsystem has recently emerged in South Africa as a way to curb the country’s persistent shortage of electricity. A wide effort for the past few decades have targeted at study, testing and demonstration of PV power systems which was established all over the country as an appropriate measure to tackle transportation, agriculture, industry, commercial as well as domestic activities. In view of these drives, both off-grid and grid-connected PV systems are being applied. However, operating a building with an off-grid system is one of the means to providing the possibility of energy access to places far away from the national grid. As an off-grid choice, 50 W SHS is being distributed to customers in distant rustic parts of the country where grid option is difficult to access. But the SHS of the stated capacity can barely generate 0.3 to 0.4 kWh of electric energy per day, even at the optimal solar radiations. In view of this, more efforts are directed at expanding the off-grid systems to accommodate large rural households in South Africa. This thesis is dedicated to a study on the various configurations and components of PV power plant as a way to enhance electricity generations in South Africa. To this effect, different power plants were considered at SolarWatt park, University of Fort Hare with the aim to conduct a comparative analysis of the charge controllers with respect to the charge and discharge rates of their respective batteries. The grid-connected PV power generation was classified into hybrid PV and grid-assisted PV, while off-grid is a BIPV. These power plants generations were installed for the purpose of research level with a total capacity of 11.4 kW. The off-grid system is made up of HIT modules, FlexMax80 charge controller, Victron energy inverter and M-Molar battery bank. The hybrid and grid-assisted systems each consist of 15 polycrystalline modules and Microcare charge controllers. In addition, hybrid comprises SMA Sunny Island inverter and Trojan battery bank whereas grid-assisted consist of Microcare inverter and Hoppercke battery bank. The first part of the experimental work was monitored, and the meteorological parameters which are ambient temperature, solar radiation, relative humidity and wind speed, were measured and evaluated while electrical parameters includes PV current and voltage, MPPT current and voltage, battery current and voltage and inverter current and voltage were also measured and evaluated in the second part of the experiment. This lasted for a period of four years, starting from 1st January 2017 to 31st December 2020. Similarly, the second aspect was to monitor the electrical performance of the three systems and was performed for a period of six months, starting from January to June 2019. During the second experiment, hybrid and grid-assisted systems were reconfigured to function as off-grid systems. Moreover, a detailed data acquisition system designed to measure and record both meteorological and electrical parameters affecting the performance of the systems. The electrical parameters include PV current and voltage, MPPT current, battery current and voltage and inverter current and voltage. Other parameters in the measurements are; inverter efficiency, active and apparent power, while meteorological parameters include; solar irradiance, ambient temperature, relative humidity, wind speed and direction. The meteorological results show that the maximum and minimum mean amount of global solar radiation was 7.34 kWh/m2/day in December and 3.03 kWh/m2/day in June, respectively, while the average radiation and temperature for the typical year were 4.98 kWh/m2/day and 16.88 oC respectively. The solar radiations obtained are within the range in major places in South Africa. Similarly, an average wind speed of 2.5 m/s is experienced in Alice in a year and average solar radiation of 606.06 W/m2 in summer and 346.17 W/m2 in winter. The three lead-acid battery systems monitored under the electrical aspect are M-Molar, Trojan and Hoppecke battery systems. It was established that the charging current decreases gradually from 27.7 to 18.5 A for the M-Molar while Hoppecke and Trojan deceased respectively from 15 to 10 A and 23 to 13 A at the end of each phase by charging it at the maximum power point of the PV array. It was equally found that the M-Molar battery current has the highest rate of charging and quickest rate of discharging in comparison to the other two batteries. Finally, from the results gotten from this research, we may propose that the solar PV system contributes significantly to the satisfaction of the needed electricity in South Africa. , Thesis (PhD) -- Faculty of Science and Agriculture, 2021
- Full Text:
- Date Issued: 2021-08
Design and Characterization of a 5 kw Xe-Lamp Solar Simulator
- Authors: Nwodo, Julian Chizoba
- Date: 2019
- Subjects: Solar energy
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: http://hdl.handle.net/10353/14671 , vital:40042
- Description: The design and characterisation of a 5kW Xenon lamp solar simulator is presented. This was accomplished through considering the design features of an ellipsoidal reflector, Xe lamp characteristics and casing, and power supply; assembly of an ellipsoidal, Xe-lamp simulator; design and building of an automated control system capable of remotely controlling the operating mode of the simulator; establishing the 3 scenarios that must be met to conform to a AAA class simulator; characterization of the simulator in terms of temporal stability, irradiance uniformity and spectral match; and application of the simulator and comparing it with STC rated values. The considerations for the type of material used for housing the components of the solar simulator were made. A 5kW DC power supply and igniter for the Xe-lamp was carefully selected since they provide necessary power for running the simulator. The simulator has the ability to be used in either horizontal or vertical position by adjusting the reflector. An automated control system capable of remotely controlling the operating mode of the simulator was built for this study, this system enables the simulator to be operated in either auto or manual modes. It also incorporates an irradiance, temperature, current and voltage feedback. The characterisation of the solar simulator was over a 2.1 m X 1.6 m test plane. The area under which the characterisation was carried out within the test plane is 110 cm x 129.5 cm. At the end of the steady state large area solar simulator characterisation, a class A spectral match, class A spatial uniformity, and a class B temporal instability was obtained
- Full Text:
- Date Issued: 2019
- Authors: Nwodo, Julian Chizoba
- Date: 2019
- Subjects: Solar energy
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: http://hdl.handle.net/10353/14671 , vital:40042
- Description: The design and characterisation of a 5kW Xenon lamp solar simulator is presented. This was accomplished through considering the design features of an ellipsoidal reflector, Xe lamp characteristics and casing, and power supply; assembly of an ellipsoidal, Xe-lamp simulator; design and building of an automated control system capable of remotely controlling the operating mode of the simulator; establishing the 3 scenarios that must be met to conform to a AAA class simulator; characterization of the simulator in terms of temporal stability, irradiance uniformity and spectral match; and application of the simulator and comparing it with STC rated values. The considerations for the type of material used for housing the components of the solar simulator were made. A 5kW DC power supply and igniter for the Xe-lamp was carefully selected since they provide necessary power for running the simulator. The simulator has the ability to be used in either horizontal or vertical position by adjusting the reflector. An automated control system capable of remotely controlling the operating mode of the simulator was built for this study, this system enables the simulator to be operated in either auto or manual modes. It also incorporates an irradiance, temperature, current and voltage feedback. The characterisation of the solar simulator was over a 2.1 m X 1.6 m test plane. The area under which the characterisation was carried out within the test plane is 110 cm x 129.5 cm. At the end of the steady state large area solar simulator characterisation, a class A spectral match, class A spatial uniformity, and a class B temporal instability was obtained
- Full Text:
- Date Issued: 2019
On the design, evaluation and performance of an energy efficient solar house with integrated photovoltaics
- Authors: Ziuku, Sosten
- Date: 2011-06
- Subjects: Solar energy , Solar energy -- Environmental aspects , Photovoltaic power generation
- Language: English
- Type: Doctoral theses , text
- Identifier: http://hdl.handle.net/10353/27473 , vital:67331
- Description: The design, construction and performance monitoring of an energy efficient house with integrated photovoltaics is considered. Unlike conventional housing, the house design combines energy efficiency measures and renewable energy technologies into one building structure. The objective of the study was to investigate the feasibility of using energy efficient solar designs to regulate indoor thermal environment, and determine thecost effectiveness and environmental benefits of such housing designs. The use of ordinary photovoltaic panels as a building element for South Africa’s latitude and meteorological conditions was also investigated. The house model was designed using Autodesk Revit architecture and Ecotect building simulation software. Electrical performance was analyzed using RETScreen and PVDesignPRO software. In addition to passive solar design features and clerestory windows, the design has solar water heaters for hot water supply. The designed energy efficient building integrated photovoltaic (EEBIPV) house was built at the University of Fort Hare. A 3.8 kW BIPV generator was mounted on the north facing roof in such a way that the solar panels replace conventional roofing material. A data acquisition system that monitors thermal and electrical performance was installed. The grid independent house has been occupied since February 2009 and its winter indoor thermal efficiency improved from 70 to more than 78% after ceiling installation. Models for indoor thermal performance and BIPV energy and exergy contributions were developed. The avoided energy consumption from the grid has potential to reduce carbon emissions by 12.41 tons per annum. The total building cost per m2 of floor area compares favourably with the cost of commercial middle-to-upper income domestic housing units without energy efficiency measures and building integrated photovoltaics. The research output provides a good framework for the integration of passive solar designs, natural ventilation and lighting, solar water heaters and building integrated photovoltaics into new and existing housing units. , Thesis (MSci) -- Faculty of Science and Agriculture, 2011
- Full Text:
- Date Issued: 2011-06
- Authors: Ziuku, Sosten
- Date: 2011-06
- Subjects: Solar energy , Solar energy -- Environmental aspects , Photovoltaic power generation
- Language: English
- Type: Doctoral theses , text
- Identifier: http://hdl.handle.net/10353/27473 , vital:67331
- Description: The design, construction and performance monitoring of an energy efficient house with integrated photovoltaics is considered. Unlike conventional housing, the house design combines energy efficiency measures and renewable energy technologies into one building structure. The objective of the study was to investigate the feasibility of using energy efficient solar designs to regulate indoor thermal environment, and determine thecost effectiveness and environmental benefits of such housing designs. The use of ordinary photovoltaic panels as a building element for South Africa’s latitude and meteorological conditions was also investigated. The house model was designed using Autodesk Revit architecture and Ecotect building simulation software. Electrical performance was analyzed using RETScreen and PVDesignPRO software. In addition to passive solar design features and clerestory windows, the design has solar water heaters for hot water supply. The designed energy efficient building integrated photovoltaic (EEBIPV) house was built at the University of Fort Hare. A 3.8 kW BIPV generator was mounted on the north facing roof in such a way that the solar panels replace conventional roofing material. A data acquisition system that monitors thermal and electrical performance was installed. The grid independent house has been occupied since February 2009 and its winter indoor thermal efficiency improved from 70 to more than 78% after ceiling installation. Models for indoor thermal performance and BIPV energy and exergy contributions were developed. The avoided energy consumption from the grid has potential to reduce carbon emissions by 12.41 tons per annum. The total building cost per m2 of floor area compares favourably with the cost of commercial middle-to-upper income domestic housing units without energy efficiency measures and building integrated photovoltaics. The research output provides a good framework for the integration of passive solar designs, natural ventilation and lighting, solar water heaters and building integrated photovoltaics into new and existing housing units. , Thesis (MSci) -- Faculty of Science and Agriculture, 2011
- Full Text:
- Date Issued: 2011-06
- «
- ‹
- 1
- ›
- »